For all gasoline engines. Suitable for standard and high-octane gas, leaded and unleaded. 150 ml is sufficient for up to 75 liters (20 gal.)of fuel.Minimum fuel filling of 25 liters (7 gal.) is requested for...
Cleaning is made with the compressed air gun for DPF (part no. 7946) and the specially developed DPF-Probe with 5 interchangeable tips (part no. 7945) or the DPF spray Probe long (part no. 20630). The...
Spray components before installing them. If the contacts are heavily corroded, allow the product to act for longer and rub off corrosion residues with a cloth or brush. Note: After spraying on, allow a flash-off...
A combination of agents, developed specifically for late model hybrid engines. Removes deposits in the fuel system and protects against corrosion. Stabilizes the fuel and protects against aging and oxidation. Diminished fuel degradation allows better...
High-tech fuel additive, developed specifically for improved throttle response under partial engine load. Optimizes fuel atomization and combustion, cleans fuel system while providing maximum engine performance and efficiency.
High-tech anti-wear additive, suitable for most 4-stroke engines as well as manual transmissions and compressors.Reduces friction and wear thanks to a unique combination of ceramic compounds and chemical anti-wear agents. It will prevent direct metal-to-metal...
One 300 ml can of Liqui Moly hydraulic tappet additive is sufficient for up to 6 liters (1.5 gal.) motor oil. The product can be added at any time. After adding, run the engine until...
One 300 ml can is sufficient for up to 75 liters (20 gal.) of fuel. Regular use keeps injection system in perfect working order and gives lowest exhaust emissions. Smoother idling, better throttle response. Injection...
MoS2 Anti-Friction Engine Treatment ensures immediate friction and wear reduction, adds an extremely protective and pressure-resistant boundary layer with low friction and lubricates during cold starts to prevent damage from lack of oil. Contributes to...
Contents sufficient for max. 5 liters (5.28 U.S. QT) of motor oil, minimum filling of 3 liters (3.17 U.S QT) is requested for optimum product performance. The product is self mixing and can be added...
Add contents to the cooling water. Turn the heating to maximum and let the engine run on idle for 10 - 30 minutes depending on the degree of contamination. Drain the coolant and flush the...
A combination of additives to clean and maintain the diesel fuel system. Prevents corrosion, increases lubrication thus reduces fuel pump and injector wear. Increases Cetane value for improved engine performance, easier starting and lower emissions....
Can contents (300 ml) are sufficient for up to5 liters (5.28 U.S. QT)of motor oil. After adding to the motor oil, allow the engine to run warm. The product can be added at any time....
Keeps rubber and plastic seals in hydraulic power steering systems soft and pliable. Leaks caused by hardened and brittle seals are prevented or eliminated. Cleans internal oil passages to allow proper oil flow, reduces noise...
To prepare, attach tube with nozzle. To gain access, remove hose or pipe immediately before throttle housing. The engine needs to run to perform cleaning. If unable to start engine, disconnect air mass sensor connector...
To prepare, attach tube with nozzle. To gain access, remove hose or pipe immediately before throttle housing. The engine needs to run to perform cleaning. If unable to start engine, disconnect air mass sensor connector...
Preventive use Fill the fuel filter up with Diesel Purge when doing filter replacement, put the rest in tank. Remedial use Unclip the fuel pipe and immerse the end in the Diesel Purge. Close the...
One 500 ml can is sufficient for up to 5 liters(1.3 gal.) of oil. Add Pro-Line Engine Flush to the engine oil at operating temperature before changing the oil. After adding the product allow the...
To be added directly into the fuel tank. As a preventive measure, add during each inspection, after repairs on the fuel system and after each Jet-Clean cleaning operation. The product mixes with the fuel automatically....
Mix the contents of the can (500ml) with 4.5l high-quality, premium-grade fuel in a clean canister. Fill the finished mixture of cleaning agents in the tank of the respective JetClean device. A detailed application description...